TMI hardware sizes are in full foot increments from 3' wide up to 10' wide. Strip mounting hardware is available in 3 materials: galvanized steel, aluminum, or stainless steel. The hardware is sturdy, durable and will last for years. More so, TMI's strip door hardware is compatible with almost every strip door on the market. Most hardware can be installed above a door in a matter of minutes.
TMI also owns a patented hardware system known as "Save-T Loc™" hardware. With Save-T Loc™, a keyhole mounting system helps keep strips in place and there is no need for nuts and bolts, resulting in a faster install time. Since the pins are pre-studded, all that is required is to mount the hardware, attach the PVC strips, then place the retainer bar over the pins and lock into place. All TMI hardware is cut specifically to individual orders, but further adjustments can easily be made with a band saw or hacksaw.
Header Mount Hardware, also known as "in-jamb" or "under lintel," is hardware that is mounted within the jamb of a door (within the doorframe.) Header mount hardware is best used in applications where space outside of the door is limited. Header mount hardware is less common because it reduces the actual height of the door, decreasing the amount of space through which objects can pass by an inch and a half. Header mount hardware is made of galvanized steel, aluminum or stainless steel and can be ordered in both Save-T Loc™ and the standard nut and bolt design. All TMI strip door hardware comes with studs spaced every 2", thus fitting the majority of PVC strips on the market. Header mount hardware has mounting holes spaced 3" from the ends and then every 6" across the hardware length.
Wall Mount Hardware from TMI is available in galvanized, stainless steel and aluminum. It is the most commonly sold type of strip door hardware and is placed directly above the door. As the hardware sits above the actual doorframe, it is highly recommended that the PVC strips be 3" longer than necessary to ensure that the strips are as close to the ground as possible. It is also recommended that your strip widths be increased by 3" to 4" inches, so that a complete seal is created around the door. Wall mount hardware from TMI is available in both standard nut and bolt as well as in the patented TMI Save-T Loc™ design. All TMI strip door hardware comes with studs spaced at every 2", thus fitting the majority of PVC strips on the market. Wall mount hardware has drill holes spaced 3" from the edge and at every 6" within the hardware to allow for easy drilling and install.
Universal Mount Hardware, as the name implies, is a versatile tool that can be mounted either to the face of the wall or within the jamb. This option proves very useful when there is uncertainty about where the strip door can be hung. Universal mounting hardware is also useful when numerous strip doors are ordered, all with different mounting needs. Universal mount hardware is available in galvanized steel, aluminum and stainless steel. Universal mount hardware comes in the traditional nut and bolt system as well as the TMI Save-T Loc™ system. It should be noted that universal mounts, if mounted on the wall, will require an extra 3" to 4" on each side of the door as well as an additional 3" of length to ensure a complete covering of the door, both on the sides and at the bottom.
Piano Hinge hardware from TMI can be requested when a door has traffic that passes through the door with little clearance between the strips and the hardware. The piano hinge hardware has a pivot point that enables the entire door to pivot on the hinge, thus reducing stress on the strips and the hardware. The hinge swings in both directions to accommodate two-way traffic. Piano hinge hardware is made of galvanized steel and is only available in the nut and bolt option. Keep in mind that piano hinge hardware will reduce the height of the door, as the hinge hangs 1.75" into the doorway.
When installing a strip door, it is fairly common to encounter obstacles such as garage doors, door track or other equipment that prevents an in-jamb or a wall mount. To overcome this, TMI offers overhead door brackets that enable the strip door to be mounted away from the door while still providing complete protection and coverage around the door. Overhead door brackets project from the wall and around the opening of the door. All brackets from TMI are zinc plated and two options are available, heavy duty and standard duty. Heavy-duty overhead door brackets provide superior strength and can be mounted on doors up to 24' wide. Standard-duty door brackets can be easily mounted on doorways up to 11' wide.
Additionally, two models of overhead door brackets are available:
When space is available on either or both sides of a doorway, sliding track hardware is an excellent and affordable choice. Sliding track hardware from TMI allows the entire strip door to be slid away from the door opening and is ideal in situations where the strip door does not always need to be in place. Sliding door track hardware is available in both header and wall mount options. There are three basic design configurations for the hardware.
This revolutionary product from TMI can be used when a there is not enough space on the left or right side of the door to accommodate a sliding strip door. Accordion fold hardware is a uniquely constructed solution, which is both economical and effective. Accordion strip door hardware enables the strip door to be slid into place when needed and then tucked to the side of the door when not. Accordion strip door hardware is excellent in regions where the climate fluctuates and a strip door is not always necessary. When the door is not being used, accordion hardware will occupy space within the doorframe. The amount of free space necessary for equipment to pass through should be taken into consideration before installing the door. Accordion strip door hardware comes in two modes, manual and motorized.
Displaying 1 to 11 (of 11 products) | Result Pages: 1 |